Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Panel Replacement Cost in Plantation?
Panel replacement in Plantation typically costs $250 – $500 for a single damaged section, including the new panel, hardware and labor. That estimate covers most single-panel swaps on standard residential doors; larger sections, discontinued panel profiles or doors that need two or three panels replaced at once push the job toward the upper end. Every job gets a written estimate first, and that written estimate sets the final price.
We’re a garage door specialist, not a general handyman outfit. Every technician on our team works on doors and openers all day, and our technicians have up to 15 years of experience across the brands most Plantation homes actually have installed: LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman and Raynor. If a panel is dented, cracked or bowed, we can usually tell you on the phone whether it’s a repair or a replacement before anyone gets in a truck. Call (833) 339-1248 for a free estimate.
Key Takeaways
- Typical panel replacement in Plantation runs $250 – $500 for one section, installed.
- Color match and panel profile availability are the two biggest price drivers.
- Replacing one panel is almost always cheaper than a new door ($700 – $2200).
- Estimates are free, pricing is upfront, and we’ll tell you when a repair beats a replacement.
Panel Replacement Cost Breakdown (2026)
Here’s how the numbers break down for a typical Plantation job. These are estimated ranges, not quotes: the written estimate you get after we see the door is the real number, and it doesn’t move.
| Line item | Typical estimated cost |
|---|---|
| Single panel replacement (standard steel, installed) | $250 – $350 |
| Single panel replacement (insulated or premium profile) | $300 – $500 |
| Two or three panels replaced together | $450 – $500+ |
| Panel plus hardware (hinges, rollers, struts) | adds $40 – $120 |
| Panel replacement with track realignment | adds $120 – $240 |
| Panel replacement with roller replacement | adds $110 – $220 |
| Related: spring repair (one spring) | $180 – $340 |
| Related: cable repair | $130 – $250 |
| Related: opener repair | $120 – $320 |
| Related: new door installation | $700 – $2200 |
What pushes a panel job up? Three things, mostly. First, the panel itself: a builder-grade steel panel costs less than an insulated panel or a carriage-house profile, and a discontinued color can cost more if it has to be sourced or matched. Second, how many panels are damaged. A single impact dent is one panel; a car that nudged the door usually takes two or three plus a track. Third, what the impact did underneath, because a bowed panel often means a bent hinge or a roller that popped out of the track. We price those as separate line items so you can see exactly what you’re paying for and decline anything you don’t want.
If the whole door is past saving, panel replacement stops making sense. A new door runs $700 – $2200 installed, and we’ll tell you honestly when that’s the better spend instead of selling you panels on a door that’s already tired.
What Affects Panel Replacement Pricing in Plantation
- Panel profile and color match. Plantation’s housing stock runs from older ranch homes to newer gated-community builds, and panel profiles changed across the decades. A current Clopay or Amarr profile is straightforward to match. A discontinued Wayne Dalton or Raynor profile can take longer to source, and that sourcing time shows up in the estimate.
- Steel versus insulated panels. Most South Florida doors are non-insulated steel, which keeps the panel price down. Insulated panels cost more but also come with a different weight, which matters for the springs and opener doing the lifting.
- Number of panels. One panel is the base case. Two or three damaged sections move the job toward the top of the $250 – $500 range, and it’s often cheaper per panel to do them together than in separate visits.
- Damage underneath the panel. A dent is cosmetic. A hit that also bent a hinge, knocked a roller loose or shifted a track is a different job. Track realignment ($120 – $240) and roller replacement ($110 – $220) get quoted alongside the panel when they’re needed, and not when they aren’t.
- Door height and width. A standard single-car door has fewer, wider panels. A double-car door has more sections, so more surface area to damage and more panel to buy. Oversized or custom-width doors cost more because the panel has to be cut or ordered.
- Humidity and storm season. Plantation’s wet summers and the occasional tropical system are hard on steel panels, especially along the bottom row where water sits. Rust that starts at the bottom edge spreads, and it’s a common reason a panel gets replaced rather than left alone. Wind-driven debris during storm season is the other one.
We handle a lot of panel replacement in this market, and the pattern is consistent: the panel itself is rarely the expensive part. It’s the extras that decide whether the job lands near $250 or near $500, and a good technician tells you which before touching anything.
How to Save on Panel Replacement
You don’t need a coupon to keep the number down. A few practical moves do most of the work:
- Fix it early. A small dent that gets replaced now is one panel. Left alone, moisture gets behind the edge and rust spreads to the panel above it, and now you’re buying two.
- Replace matching panels together. If two panels are damaged, doing them in one visit is cheaper than two separate appointments, and the color match is better because the panels come from the same production run.
- Ask for the repair-first opinion. A dented panel doesn’t always need replacing. Sometimes a hinge or roller is the actual problem and the panel is fine. We’ll say so. Our whole approach is to repair before we recommend replacement, and we’ll put that in writing on the estimate.
- Keep the door balanced. A door that’s fighting its springs puts stress on panels and hinges. If the door feels heavy or slams down, that’s a spring or cable issue (spring repair $180 – $340, cable repair $130 – $250), and fixing it protects the panels you already have.
- Get the free estimate before you commit. Estimates are free and pricing is upfront, so there’s no cost to finding out the real number. Call (833) 339-1248 and we’ll book a time to look at the door.
One safety note, because it matters more than saving a few dollars: the springs and cables that lift a garage door are under extreme tension, and they’re the most dangerous part of any garage door job. Never try to loosen, remove or adjust a spring or cable yourself, and never take a panel off a door that’s still under spring tension. That’s work for a trained technician, and it’s work we do every day. If you’re not sure whether your door is safe to operate, stop using it and call.
When a panel is damaged, we also look at the opener while we’re there, since a door that’s been hit often drags on the way up. If the opener is straining, that’s garage door repair territory and worth catching before the motor burns out. Same visit, one estimate.
FAQs – Panel Replacement Cost
How much does panel replacement cost in Plantation?
Panel replacement in Plantation typically costs $250 – $500 for a single section installed, with the exact figure depending on panel profile, insulation and whether anything underneath the panel was damaged. Call (833) 339-1248 for an exact quote; estimates are free.
Is it cheaper to repair or replace a garage door panel?
Repairing or replacing one panel ($250 – $500) is almost always cheaper than a new door ($700 – $2200), so replacement only wins when the door is structurally tired, badly rusted along several panels, or the profile is discontinued beyond matching. We’ll give you both numbers and let you decide.
Can you match my existing panel color and profile?
Usually, yes. We work with Clopay, Amarr, Wayne Dalton, Raynor and the other common brands, and current profiles are straightforward to match. Older discontinued colors can take longer to source, and if an exact match isn’t available we’ll tell you before you spend anything.
Can you come today?
Often, yes. We offer same-day service and fast dispatch from 7am to 7pm, and panel jobs are usually quick once the right panel is on hand. Call (833) 339-1248 and we’ll tell you what’s possible for your door.
Does a dented panel need replacing, or can it be repaired?
Not every dent needs a new panel. If the panel is still straight and the hinges and rollers are sound, it may be a repair. If the panel is bowed, cracked or rusted through, replacement ($250 – $500) is the right call. A technician can tell the difference in a few minutes, and the estimate is free.
Panel damage is one of the easier garage door problems to solve, and one of the easiest to make worse by waiting. If a panel on your door is dented, cracked or rusting at the bottom edge, call Plantation Garage Door Repair Co at (833) 339-1248 for a free estimate. We’re garage door specialists from spring to opener, we know the brands in your neighborhood, and we’ll give you a straight number before any work starts.
Pricing reflects the Plantation market as of 2026. Plantation Garage Door Repair Co offers free estimates – call (833) 339-1248.
What Our Customers Say
"Opener works, remotes are programmed, no complaints on the work. Took three days to get on the schedule though, so if you've got a car trapped inside, say so when you call."
- Craig Anderson"Replaced the bottom panel after I backed into it. Color match is close enough that you have to know to look for it."
- Priya Sharma"Track was bent and two of the rollers were shot. He straightened what he could, swapped the rollers for nylon ones, lubricated everything, and had it done in about an hour."
- Craig Quinn